Produse pentru 2 epoxid componentă (12)

Syntech Poliurea Primer – Epoxy Metal Syntech Poliurea Primer – Epoxy Metal is a two-component primer based on epoxy resins free from solvents, used to promote adhesion, as a surface sealant for concrete, applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. Adhesion promoter, surface sealant for concrete, to be applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. The application must take place on a dry and degreased surface; the substrate must not have crumbly or detached parts and with a degree of humidity that must not exceed 5%. Preparation of the substrate may require some types of mechanical action: Smoothing, bush-hammering, shot peening, hydro-washing. Other mechanical actions that can make the support suitable. The individual components must be mixed carefully until a homogeneous mass is obtained. The material can be applied by roller, brush or spray by means of special airless machines, even in two coats. The temperature of the support must always be at least 3°C higher than the dew point temperature. Minimum application temperature +5°C, maximum temperature +35°C. Approximately 0,20 kg of Syntech Poliurea Primer – Epoxy Metal for every square metre of surface to be treated. Can 10 kg [A] - Can 5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B]

Applicable as Non-stick coating also used for high-temperature applications up to 350°C • Typical layer thickness approx. 20 – 40 μm • Pencil hardness 9H • Clearance certificate for contact with food available Easy-to-clean coating also used for high-temperature applications up to 350°C • Typical layer thickness approx. 5 – 10 μm • Pencil hardness 9H • Clearance certificate for contact with food available Light corrosion protection Typical applications - Foodstuff industry - Bakery industry - Chutes, conveying systems, rollers - Injection moulding, moulding production - Heating plates, heating mirrors - Blades - Varnishing troughs - Impellers - Heat exchanger - and more besides

Thermische Spritzverfahren Lichtbogenspritzen Atmosphärisches Plasmaspritzen Pulverflammspritzen Drahtflammspritzen Hochgeschwindigkeits-Flammspritzen (HVOF) Nachbehandlung von Spritzschichten Versiegeln Ofensintern Drehen/Schleifen/Läppen/Honen Qualitätssicherung von Spritzschichten Prüfen und Messen der Bauteile Prüfen auf Rissfreiheit Messen der Oberflächenhärte Messen der Oberflächenrauheit Erstellen eines metallographischen Schliffes

Système époxy transparent. Dureté variable. Facile d'emploi. -> Application Décoration, décoration florale, imitation de liquide, simulation de cours d'eau en maquettes. Couleur : Transparent Ratio mélange : 100/100 Potlife : 70 min à 9h Temps avant démoulage : >48h TG°C : nc Unité de vente : 1 kit de 2kg Minimum de commande : 1 kit

Film de protection de couleur permettant de changer la couleur d'un véhicule tout en aillant la protection du film PPF (auto cicatrisation, brillance, protection UV, protection film routier...

CKW-freier, lösemittelhaltiger 2K-Kontaktklebstoff auf CR-Basis für Gummi, Metall, Gewebe, Neopren z.B. als Kaltklebstoff für Fördergurte, Verschleißschutzauskleidung, Trommel- / Walzenbelegung

Zweikomponenten-Epoxidharzbeschichtung zum Schutz von Fußböden mit ausgezeichneter Beständigkeit gegen Chemikalien und Abrieb sowie Rutschbeständigkeit aufgrund der Zumischung eines langlebigen Zuschl

Syntech HAG Acryl Syntech HAG Acryl is a four-component resin that reacts to form an elastic and durable gel. The properties of Syntech HAG Acryl are: • Good general chemical resistance. • Does not contain acrylamide, methacrylamide, formaldehyde or solvents. • Not inflammable. • Excellent adhesion on mineral building materials such as concrete, cement and bricks. • The reaction speed can be adjusted from a few seconds to several minutes. • When the injected cracks dry out due to temperature or groundwater level fluctuations the gel does not crack easily. • The hardened gel has excellent durability in wet-dry cycles. Syntech HAG Acryl components are supplied ready to use. Create 2 mixes in separate plastic buckets. Prepare only the quantity to be used each time. Solution 1: Syntech HAG Acryl component A (25 kg resin) mixed with Syntech HAG Acryl component B (2.5 kg catalyst). Solution 2: Syntech HAG Acryl component C (2 packs of 0.625 kg) mixed with clean tap water. Attention: The amount of water must be equal in volume to solution 1. When mixing resin, always use a wooden or stainless steel spatula. The reaction time depends on the temperature of the material, the structure of the building and the possible amount of water present. Higher temperature will speed up the reaction time and lower temperature will slow it down. It is advisable to carry out an on-site test, before injection, to observe and define the reaction time. To change the reaction time, only adjust the amount of Syntech HAG Acryl component C. The amount of the other components remains the same. Use a two-component stainless steel pump (manual, electric or pneumatic). Check that the pump and equipment are clean and that there is no residue from previous injection work. The two mixtures are fed into the pump separately, but are mixed homogeneously at a volumetric ratio of 1:1 in the pump's mixing head, before being injected through the pump nozzle. Check the quality of the concrete, as injection involves pressure. Sealing and waterproofing of cracks and cavities in walls, floors, concrete constructions, underground structures, etc. It can be used in constructions that are not permanently in contact with water (fluctuating groundwater level). Injection of very fine cracks. Determine the type and size of packers based on your pump and injection type. If reinforcing steel is present, try to locate it and plan the drilling pattern so that the reinforcement is not drilled. Drill holes at an angle of approximately 45° or less and in the direction of the crack. Make sure the hole goes through the crack. The distance of the drilled holes depends on the width of the crack. Place the packer in the hole. Prepare the pump to start the injection. The injection pressure varies depending on the structure and size of the crack. Start the injection at the lowest point of the crack. Continue injecting until resin flows out of adjacent packer(s). This is necessary to achieve uniform distribution of the material. Stop pumping, unplug and move on to the next packer. Continue the procedure until the crack is completely filled. After the material has cured, the packers can be removed. Holes drilled can be covered with Repar Tix Speedy HP quick-setting mortar. Clean and rinse the pump equipment with water whenever there is a stoppage longer than 15 minutes and, after completing the injection, rinse with a sufficient amount of water. Make sure the pump is clean and stop only when clean water comes out of the pump. The consumption of the product depends on the size of the empty volume to be filled. Can 25 kg [A] - Plastic can 2.5 kg [B] - Canister 0.625 kg [C] - Canister 0.625 kg [D] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.5 kg [B] + 1 Canister 0.625 kg [C] + 1 Canister 0.625 kg [D]

Développé et amélioré au fil des années, le PPF est à ce jour un traitement haut de gamme à l’aspect transparent préservant l’aspect esthétique du véhicule. Applicable aussi bien sur une voiture qu’une moto, il recouvre l’intégralité des surfaces de la carrosserie ou seulement des zones définies selon les besoins du propriétaire : phares, pare-chocs, etc. Pour un entretien complet de votre véhicule à Fréjus, découvrez les autres techniques de protection de carrosserie, comme le traitement céramique ou le nettoyage en profondeur intérieur et extérieur de votre voiture.

REFERENCE : RESMPP16095 (ex PP1609)36kg/m2. RESIFOAM BAYMER AL759 5kg...kg MOUSSE POLYURETHANE RESIFOAM. Mousse polyuréthane expansive rigide approprié pour le remplissage d'élements par coulée. Applications:isolation industrielle,remplissage, reserves de flotabilité etc... MELANGE: 100parts RESIFOAM + 100parts DESMODUR(en volume)

Acrystal prima liquide est un matériau composite blanc, sans solvant, à deux composants : - une résine acrylique liquide aqueuse "Acrystal Prima" - une poudre à base de cristaux minéraux : "Basic Crystal" -> Domaine d'application - Décorations architecturales - Répliques - Maquettes - Scénographie - Muséographie - Art & artisanat - Modèles - Moules - Chapes de moule - Prototypes -> Caractéristiques Unité de vente : Pot de 25KG Minimum de commande : 1 pot Dosage en poids : 1 kg de liquide Acrystal Prima 2,5 kg de poudre Basic Crystal Dureté Shore D : 81 - 83 Temps de travail : 8 - 10mn

ZA 22 SPRAY, est un silicone RTV par addition bi-composant (base et catalyseur) qui vulcanise à température ambiante. Indiqué pour la duplication de modèles avec peu de contre- dépouilles et pour applications sur des surfaces verticales. -> Domaines d'application Fabrication de moule et restauration pour applications verticales. -> Caractéristiques Unité de vente : kit de 25kg base + 25kg catalyseur Minimum de vente : 1 kit Dureté : 22 Shore A. Dosage en poids : 1 / 1 Temps de travail : 12 à 18mn à 23°C